The Concept
The basic concept behind this machine is that gravity is a force that pulls everything towards the center of the earth. If something is thrown from the hilltop, it will come down to the foothills. Or, if a load is let loose on top of a spiral path, the load will come rolling down without the need of any additional effort till it reaches the bottom. The important thing to keep in mind is that gravitational force is directly related to the weight of the load. If the load is heavier, it comes down a lot quicker.
So, the basic design of the machine is based on the above principle only. With help of its own weight, this machine rotate on the spiral threads of a rod on which it is placed thereby rotating the turbine and generating electricity.
As shown in the above schematic diagram, with help of support bars, the generator is placed on the top of threaded rods. These rods go through the middle of the electricity generating unit. With help of the weight of the generating machine, it starts to fall down. And since the only way it can come down is by rotating, the turbine inside the generator starts rotating and generates electricity.
I have used the concept of seamlessly interconnecting rods. Once the generating unit falls down, the rod can be opened from above and placed below the generator once again thereby creating a cycle. The rod lifting machine is used to lift the rods upwards so that more and more rods can be connected below.
In the above machine, the electricity input is at 2 locations. One is for the rod rotating machine that opens the rods from top and connects them at the bottom. And the other is in the rod lifting machine that lifts all the weight upwards.
As per the standard knowledge, it is good to believe that these electricity inputs will be more than what the generator will produce. This is because, when the generator is at top, it is loaded with potential energy and when it comes down, this potential energy is converted to mechanical energy and then to electrical energy. And to take the generator back at top with help of the lifter, much more electricity will be used.
My point is that it would be unwise to equate both these motions. This is because, when the generator is falling down, it is not a free fall. The hard to rotate turbine is rotating that would have otherwise taken a lot of force. And when we are lifting the machine, we are only lifting the weight. If we increase the generation capacity of the turbine, the weight does not increase in the same proportion. In effect, we end up getting a positive figure on the net energy calculations.
This type of machine is still on the concept stage, though a lot of activities are in progress for the development and testing of such a machine. The only reason for a delay is lack of funds for the project. If anyone is interested in joining hands, I would be more than happy to work together. Anyone Interested??
The basic concept behind this machine is that gravity is a force that pulls everything towards the center of the earth. If something is thrown from the hilltop, it will come down to the foothills. Or, if a load is let loose on top of a spiral path, the load will come rolling down without the need of any additional effort till it reaches the bottom. The important thing to keep in mind is that gravitational force is directly related to the weight of the load. If the load is heavier, it comes down a lot quicker.
So, the basic design of the machine is based on the above principle only. With help of its own weight, this machine rotate on the spiral threads of a rod on which it is placed thereby rotating the turbine and generating electricity.
As shown in the above schematic diagram, with help of support bars, the generator is placed on the top of threaded rods. These rods go through the middle of the electricity generating unit. With help of the weight of the generating machine, it starts to fall down. And since the only way it can come down is by rotating, the turbine inside the generator starts rotating and generates electricity.
I have used the concept of seamlessly interconnecting rods. Once the generating unit falls down, the rod can be opened from above and placed below the generator once again thereby creating a cycle. The rod lifting machine is used to lift the rods upwards so that more and more rods can be connected below.
In the above machine, the electricity input is at 2 locations. One is for the rod rotating machine that opens the rods from top and connects them at the bottom. And the other is in the rod lifting machine that lifts all the weight upwards.
As per the standard knowledge, it is good to believe that these electricity inputs will be more than what the generator will produce. This is because, when the generator is at top, it is loaded with potential energy and when it comes down, this potential energy is converted to mechanical energy and then to electrical energy. And to take the generator back at top with help of the lifter, much more electricity will be used.
My point is that it would be unwise to equate both these motions. This is because, when the generator is falling down, it is not a free fall. The hard to rotate turbine is rotating that would have otherwise taken a lot of force. And when we are lifting the machine, we are only lifting the weight. If we increase the generation capacity of the turbine, the weight does not increase in the same proportion. In effect, we end up getting a positive figure on the net energy calculations.
This type of machine is still on the concept stage, though a lot of activities are in progress for the development and testing of such a machine. The only reason for a delay is lack of funds for the project. If anyone is interested in joining hands, I would be more than happy to work together. Anyone Interested??
4 comments:
This is awesome! I may keep this in mind for the future, although, I just got a generator rental and it has worked really well for me.
http://www.pragadeesan.blogspot.in/2013/04/hybrid-power-generator.html
the purpose of this message is to introduce you to a website www.premrawat.com to know more go to www.premrawat.com/video/
i have been researching for this for about 6 years though the results are not that good but i will keep on working till i get succeed. my motive is to produce electricity without any external supply of energy and ya that is possible only with the help of gravity. like you said we require more energy than it is being produce to keep the generator working. my research is about this only lets keep working for what we want to acquire.
Post a Comment